About local rate limiting

Without local rate limiting, all requests are directly forwarded to the rate limit server where the request is either denied or allowed based on the global rate limiting settings that you configured. However, during an attack, too many requests might be forwarded to your rate limit servers and can cause overload or even failure.

To protect your rate limit servers from being overloaded and to optimize their resource utilization, you can set up local rate limiting in conjunction with global rate limiting. Because local rate limiting is enforced in each Envoy instance that makes up your gateway, no rate limit server is required in this setup. For example, if you have 5 Envoy instances that together represent your gateway, each instance is configured with the limit that you set. In a global rate limiting setup, this limit is shared across all Envoy instances.

For more information about local rate limiting, see the Envoy documentation.

Architecture link

The following image shows how local rate limiting works in Gloo Gateway. As clients send requests to an upstream destination, they first reach the Envoy instance that represents your gateway. Local rate limiting settings are applied to an Envoy pod or process. Note that limits are applied to each pod or process. For example, if you have 5 Envoy instances that are configured with a local rate limit of 10 requests per second, the total number of allowed requests per second is 50 (5*10). In a global rate limiting setup, this limit is shared between all Envoy instances, so the total number of allowed requests per second is 10.

Depending on your setup, each Envoy instance or pod is configured with a number of tokens in a token bucket. To allow a request, a token must be available in the bucket so that it can be assigned to a downstream connection. Token buckets are refilled occasionally as defined in the refill setting of the local rate limiting configuration. If no token is available, the connection is closed immediately, and a 429 HTTP response code is returned to the client.

When a token is available in the token bucket it can be assigned to an incoming connection. The request is then forwarded to the rate limit server to enforce any global rate limiting settings. For example, the request might be further rate limited based on headers or query parameters. Only requests that are within the local and global rate limits are forwarded to the upstream destination in the cluster.

Order of rate limit priority link

The local rate limiting Envoy filter allows you to configure the number of tokens in a token bucket for a gateway, virtual service, virtual host, or route. Depending on where you configure local rate limits, the limit might be enforced on that resource only or be applied to all underlying resources. For example, if you configure a limit on the gateway resource, the limit is automatically shared across all virtual services, hosts, and routes. However, if you also specify a local rate limit on an underlying resource, such as a particular route, the route does not share the limit of the gateway anymore, but instead enforces its own local rate limit as shown in the following diagram.

The rate limit priority order is defined as follows. Local rate limiting settings on a gateway are always shared with all underlying resources. If a resource defines its own local rate limiting settings, these settings take precedence.

Gateway > Virtual Service > Virtual Host > Route

To try out an example, see the HTTP gateway local rate limiting guide.

Types of local rate limiting on a gateway link

Review your options for configuring local rate limiting on a gateway.

HTTP gateway link

You can choose between the following options to configure local rate limiting on your HTTP gateway resource.

• HTTP local rate limiting: You can apply local rate limiting settings to all Layer 7 traffic by adding the httpLocalRatelimit setting in the HttpListenerOption resource. Settings that are defined in this filter are enforced by the HTTP Envoy filter after the TLS handshake between the client and the gateway is completed successfully. To verify that your rate limiting settings are working as expected and to simplify troubleshooting later, you can optionally set the enableXRatelimitHeaders: true option. This option adds rate limiting headers to a response as defined in the Envoy documentation.
• Network local rate limiting: If you want to configure the HTTP Envoy filter to apply local rate limiting settings to all Layer 4 traffic, you can add the httpGateway.options.networkLocalRatelimit option to your gateway resource. If set, local rate limiting is enforced before the TLS handshake between the client and the gateway is started. Because this option is enforced on Layer 4, no HTTP response code, headers, or messages are returned when rate limiting is enforced.

To try out an example, see the HTTP local rate limiting guide.